Uses of Class
com.tccc.kos.ext.freestyle.hardware.can.troubles.BasePumpTrouble
Packages that use BasePumpTrouble
Package
Description
-
Uses of BasePumpTrouble in com.tccc.kos.ext.freestyle.hardware.can.troubles
Subclasses of BasePumpTrouble in com.tccc.kos.ext.freestyle.hardware.can.troublesModifier and TypeClassDescriptionclassBase class for various AirVentAware flow errors.classCANPumpTrouble<T extends AbstractCANPump>Base class for all CAN pump troubles.classTrouble indicating CGP no flowclassTrouble that indicates that the version of CGPPump installed is not supported on this device.classFlow below error threshold.classWhen macksm fails to read FCM EEPROM (and use the default FCM cal value) Event sequence: 121 - JET_ST_FCM_CAL_DEFAULT_VAL_USEDclassFCM failed to stop.classFlow over error threshold.classFCM gear meter encoder failure Event sequence: 83 - JET_ST_FCM_GEAR_METER_ENC_FAILUREclassNo flow detected for hfcs (so we can have different messaging) Event sequence: 89 - JET_ST_FCM_NO_FLOWclassFCM detected high pressure.classFCM failed to home.classFCM detected low pressure.classNo flow detected.classPump is delivering at a higher rate than requested.classFlow over error threshold.classBase trouble for flow meter related troubles.classFCM base trouble that causes the board to be rebooted.classTrouble that indicates that fcm is sold out.classFCM step motor encoder failure Event sequence: 84 - JET_ST_FCM_STEP_MOTOR_ENC_FAILUREclassFCM step motor is jammed.classFCM step motor is no longer jammed.classUnexpected flow detected.classUnexpected high flow rate detected.classUnexpected slow flow rate detected.classPump is delivering at a lower rate than requested.classFCM detected low pressure.classFCM failed to reset.classFCM failed to start.classFCM failed to stop.classOccurs on I2C MUX Reset Peripheral (same as cal value err 122) Event sequence: JET_ST_I2C_MUX_BUSY_RESET(123)classTrouble that indicates that LFCV is sold out.classPumping air, no ingredient left.classNo current sense on the pump.classMicro Pump Default cal value used Event sequence: JET_ST_MICRO_PUMP_DEFAULT_CAL_USED(122)classFuel gauge hit -30 ml within the pump.classPump is occluded.classNNS not available due to sold out.classPump is delivering at a higher rate than requested.classPump is occluded.classToo much current on the pump.classPump is delivering at a higher rate than requested.classSPM ingredient not available due to too many MicroPumpSPMOccludedTroubles.classThis trouble is generated by DefaultPumpErrorHandler when it detects a sold out condition on a pump that doesn't have an associated cartridge.classSPM pumps did not complete Event sequence: JET_ST_SPM_NOT_COMPLETE(142)classSPM Pump is occluded.classSPM pump still ON while inactive Event sequence: JET_ST_SPM_ON_WHILE_INACTIVE(141)classPump is too hot to run.classPump is delivering at a lower rate than requested.classTrouble that indicates that MSV not ready yetclassPump is delivering at a higher rate than requested.classTrouble that indicates that MSV is sold out.classPump is delivering at a lower rate than requested.classAir vent high probe is wet, low is dry.classPump is unable to fill air vent.classResult of AirVentProbesDryPumpOp detecting wet probes.classResult of AirVentProbesWetPumpOp detecting dry probes.classBubble detect loopback signal lost.classPump is delivering at a higher rate than requested.classBase class for various flow errors.classPump is delivering at a lower rate than requested and wants to fold back.classLow probe on the air vent is dry.classOver delivery alert threshold reached.classOverdelivery value is unreasonable.classPump is unable to detect position.classUnder delivery alert threshold reached.classUnderdelivery value is unreasonable.classCGP Solenoid Failed to OpenclassDrool Valve Open Failed detected troubleclassDrool Valve Open Unable to OpenclassTPM bubble detect. -
Uses of BasePumpTrouble in com.tccc.kos.ext.freestyle.troubles
Subclasses of BasePumpTrouble in com.tccc.kos.ext.freestyle.troubles